The best way to Use a Stump to be Killed by Lime

Trees that have out-grown their surroundings or have been damaged by weather may be inconvenient for homeowners. They are able to even pose security risks. Removing trees is left to the experience of a certified business, but it might be up for you to clear the floor of the stump, when the tree was felled. It’s possible for you to remove the stump with small manual labor by simply applying lime to eliminate the stump and after that digging up the root ball that is remaining. A sleek, manicured garden is well worth the wait, although the procedure can take weeks.

Remove as much of the stump that stays above-ground as feasible. Drill 1 inch holes to the very best of the stump, round the perimeter, about three or four inches in the edge of the stump. The holes should be one foot deep. In the absence of a drill, it is possible to cut notches that are deep with the ax as an alternative approach.

Unearth the roots of the stump by digging round the outside the stump, eliminating the topsoil to expose the root ball. In the event the stump is huge, this may be the most labor intensive element of the procedure.

Purchase lime at garden shop or your home improvement. Lime may be purchased in 5- or 10-pound bags. You’ll need lime to cover the very top of the stump as well as the roots also to fill the holes, before purchasing the lime, therefore determine the dimensions of your stump.

Protect your palms with rubber gloves. Pour lime to the holes which you cut or have drilled to the most notable of the stump. Spread mo Re lime on the the top of stump and entirely protect the uncovered roots using the lime.

After implementing the lime cover the tree stump. A tarp is a protect that is sufficient. Use a rope to secure the tarp throughout the foot of the stump. Place huge stones or hefty bricks on the edges of the tarp to ensure animals and kids WOn’t be subjected to the lime.

Allow the lime while being guarded in the elements with all the tarp to soak to the stump for three to five months. When the stump has been killed by the lime, it will become spongy and rotted, permitting one to easily split it up using an ax and dig the stump and root ball out utilizing a shovel.

See related

The best way to Clean a Constant Ground Drain

A backup may be a messy experience for those who have a steady ground drain in your garage or laundry area. A ground drain that is clogged can leave water standing in your ground, ruining electronics and your resources. The drain when you observe the water draining gradually for the most useful outcome. If it does n’t be cleaned by flushing the drain out, lease or purchase a plumber’s snake to assist you clear the clog.


Remove the drain cover before you attempt to clear your drain. It may lie even using the ground or may possess a screw, with its fat keeping it in place. Loosen the cleanout plug using an adjustable wrench and pull out it. Remember to set the cleanout plug in the drain as it blocks harmful sewer gases from entering your house if you are finished.

Hot Water

If water is draining down the drain, some residue can be broken up by utilizing a quick flush of warm water. Boil some water, obtaining 2 gallons warm as possible. You may not have a pot large enough to boil 2 gallons that are total, however you can add water to warm water, which ought to work. Pour it swiftly down the drain. This approach only works in the event the drain is not totally clogged, causing water to stand in your ground.

Baking Soda and Vinegar

The chemical reaction between vinegar and baking soda can help speed up a sluggish drain, when your drain is totally blocked, even though it is perhaps not successful in standing water. Vinegar and baking soda react, creating a clear that is bubbling motion as part of your drain. Pour 1 cup of each. Follow that with 3 glasses of of water. Wait until the bubbling has stopped, then pour mo-Re water-down the drain to create sure there aren’t any clogs that are remaining. Repeat the baking-soda and vinegar process in the event the water is draining gradually.

Plumber’s Snake

Plumbers clear gradual drains and usually use augers, or snakes, to open drains which can be clogged. It’s possible for you to buy or hire these for the most part DIY stores retailers. Some are created for tiny drains, including to get a bath-room sink, so make certain to get a greater one for ground drains. Put the finish of the auger to the drain in the event you are utilizing a auger and twist it down. For augers, established the pipe to to show clock-wise and press the foot pedal to engage it. Lower the pipe gradually before a resistance is felt by you, then twist it straight back out somewhat. Go ahead and backward several instances to attempt to dislodge a clog. Pull the auger pipe from the drain in the event that you are having having problems continue and clear particles off to make it pierce through the remaining clog.

See related

4 Ways to Repair a Broken Door Lock

According to professional handyman services Indianapolis, homeowners often call them out for jobs that are so simple that they could repair on their own without having to fork out hefty call-out fees. Luckily for you, we’ve compiled a list of practical techniques that you can try today to repair your own locks and save money on locksmith fees.

Identify the Problem Early

Oftentimes, a lock will start showing minor problems like jamming when you want to open it, or your doorknob will start to feel loose. These are often the initial signs of a faulty lock mechanism or lock assembly, and it makes way more sense to fix them early on instead of waiting for the lock to break completely.

Grease It Up

A poorly functioning latch can be caused by a simple issue such as an improperly fitted door or a dirty or dry lock. A dry lock can be easily fixed by lubricating the lock with some graphite. While it may seem like the obvious solution, oils are not recommended to grease up locks because they tend to gum-up the works.

On the other hand, if it’s a sticky key that’s giving you problems, then you can start by trying it a few times before you take another action. If the key works after you’ve tried it again, the problem might be that the deadbolt is unable to engage the strike plate as it should.

Also, if the key itself can’t turn the lock or requires a considerable amount of force to do so, then you might want to clean or lubricate the lock too. Then, finish off by spraying the inside of the cylinder with graphite before trying it again a few more times.

Dissect the Lock

Sometimes you’ll find that the key is not doing its job of unlocking the door even though it’s turning when you place it in the lock. The recommended solution here is to take the lock apart because this problem usually occurs when the tang or cam are not correctly joined with the bolt.

You might also come across some broken parts after you’ve disassembled the lock, and you’ll want to replace these before you put the lock back together again.

Sometimes, the key gets so frozen during winter that it’s unable to fit into the lock mechanism. An easy fix to this problem is to heat up the key and then try to gradually put the key inside the keyhole. If this trick doesn’t work the first time, then keep repeating it until the key has completely thawed.

File the Key

Surprisingly enough, handyman Indianapolis often get called in for problems with new keys as well, especially the ones that can’t seem to open the lock. This too can be easily fixed by filing down the key in certain spots. First, you start by blackening the key with soot, which is done by holding the key over a flame, and then place it into the lock and gently turn it.  

If the key comes out with shiny areas after you’ve pulled it out, then file them down until the key comes out completely covered with soot instead. This shows you that there are no longer any rough areas on the key to prevent it from working properly.

Well, there you have it! Great tips on how to repair your own locks taken from some of the most experienced Indianapolis handyman in the industry. Just keep in mind that these tips will not work for all scenarios, and that sometimes you’ll have to hire a locksmith to completely replace a broken lock.

The best way to Create a Shelf

Installing shelving on a wall of your house lets you create space for storage on an area which is otherwise unused. Having brackets in simple view can detract from your room’s look; installing “floating” shelves removes the need for brackets. These are shelves are connected to the wall using a cleat which is covered by the shelf, providing the shelf the look that it “floats” against-the-wall. An effortless way to finish the project requires reducing an 18-inch hollow-core door in two length-wise and utilizing each piece.

Using a stud finder, locate the studs and mark their place. When setting the cleat draw a line on the other side of the wall to offer a manual. Use a level to make sure that the line is straight.

Saw an 18-inch hollow-core door in two length-wise. Use a 40-tooth carbide blade in a circular saw to slice the the door, when performing it, and use safety goggles.

Measure the inside edges of the door panel on the side where it is minimize by you. Cut a cleat to to match these dimensions from a 2 by-4 board, using the saw.

Place the cleat from the wall together with the aid of an assistant. Position the leading fringe of of the cleat from the line you drew on the wall to mark the area of the shelf. Drill 1/8 inch pilot holes throughout the cleat and in to each stud.

By driving lag screws throughout the pilot holes connect the cleat to the wall. Use wrench or a drill to tighten the screws.

By scraping out the cardboard core in the shelf using a wood chisel create space for the cleat in the shelf. Remove 1.5-inches of the card-board.

By putting it check the match of the shelf. Hollow-out mo Re of the card-board until it does, in the event the back fringe of of the shelf does not rest flush against-the-wall.

Apply a bead of carpenter’s glue to the edge over the base of the shelf, where you hollowed-out the card-board core as well as the very top of the cleat.

Slide the shelf within the cleat. Place a framing square in addition to the shelf from underneath to square it, and raise it.

Drive 1inch brad nails throughout the bottom fringe of of the shelf and to the cleat. Use one nail every 8″ over the shelf. Wipe a-way any carpenter’s glue that seeped out having a moist rag.

See related

The best way to Know in case Your Tub Drain Is a Drop-in or Threaded?

The tub drain is an after thought for a lot of homeowners — till it gets clogged. Before start cleaning it out, you you should know know what kind of drain you have.This will decide which components need to be cleaned or that which you what you should to displace an existing drain. You will find lots of different types two of the most frequent are threaded and Drop in drains. Threaded drains are typically identified in tubs that were older, while the fall-in model is typical in newer versions. Determining whether you’ve another or one involves a little inspection.

Drop-In Drain

Check your drain stopper. A Drop in drain has a stopper having a knob that is notable.

Lift the stopper by means of your thumb and fore finger to its fullest capability.

Reach to get a nut beneath the the stopper as well as a feel. Merely twist the nut by means of your thumb and forefinger before the stopper comes free, in the event that you would like to eliminate the stopper.

Threaded Drain

Check to find out in case your drain has an over-flow plate. It is a plate underneath the faucet using two screws and a lever. If it does, you’ve a drain that is threaded.

Have a look in the stopper in the underside of the tub. A drain that is threaded typically has a steel display which is screwed into place.

Flip the lever on the over-flow plate to the place that is open.

Unscrew the over-flow plate. Attached to the back of it’s a steel linkage that threads into the drain. On some tubs, you could possibly be in a position to pull out the linkage entirely.

See related

Tips for Choosing a Good Junk Removal Company

In most areas, junk removal companies are few and far between, and most don’t really have a widespread presence or reputation in their communities due to the specialized nature of the service they provide. The industry is also riddled with scammers that provide below-par service, which only adds to the difficulty in making an informed decision about hiring the right tree trimming Denver, CO company.

However, don’t despair because we’re here to help you choose the right service provider, with tips on what to look for and how to tell if you’re choosing the right service provider.  


Find out the variety of services offered by the company to gauge their level of competency and sustainability. In addition to furniture removal, a good tree service Denver, CO company should offer more complex services like demolition or construction site clearance etc. This means that the company has a lot of resources at its disposal which gives them the ability to tackle any level of difficulty when on the job.  

Customer Service

How often does the company update its website? How many contact options do they offer? Do they show a high level of attention and availability to customers? Asking these and other simple questions and trusting your gut is a really easy way to find out the type of service offered by the company.


Find out how big their trucks are and how many are in their fleet. This will give you an idea of how fast they’ll be able to complete the job and how much junk they’re able to move in a day. Their available equipment will also factor into their pricing as well.


You should always be wary of junk removal companies that offer you a bargain rate, or one that doesn’t agree to provide an estimate for your junk based on cubic yardage, as that means that they’ll probably try to base their pricing on variables like manpower or time, both of which are beyond your control and could, therefore, lead to overpricing.   


Any well-run junk removal company will take care of its equipment by keeping its trucks clean and well-maintained. They will also make sure that the workspace is left clean and clear once they’re done with the job. On the other hand, a company that doesn’t post images of their equipment online is a sure sign of ill-management and probably means that their service is just as bad.


Recycling should be a priority for any tree removal Denver, CO company, because otherwise, where will they place the junk once they’ve removed it? It’s also your responsibility to make sure that the company you choose has a recycling policy in place whether it involves recycling the junk in-house or partnering with a third party to recycle it. It is important to keep as much junk away from the landfills as possible, and any service provider that doesn’t embrace recycling as part of their policy is definitely not worth considering.


It is essential to ensure that the Denver tree service company you choose is actually insured to avoid costly disasters and mistakes.

Past Jobs

Word of mouth is still the biggest indication of a company’s capability, and testimonials from past customers as well as any past jobs that are documented on the company’s website or blog could be very helpful in helping you to make your decision.

The best way to Install Twist & Fit Curtain Rods

One typical kind of curtain rod needs brackets that connect to the wood-work or the wall. Twist-and-fit rods can not connect something to the wall and provide an option when you do not want to mar your wall or are leasing. These simple-to-install curtain rods conform to to any size window-frame. Different lengths and diameters are available to give the correct dimensions curtain rod to each window. Twistandfit curtain rods save installation time, also.

Measure the the length in one, of the window opening aspect of the the inner to another side, using a tape measure. Ensure you’re measuring the distance in the window opening, excluding any trim parts that body the window.

Slide the rubber ring onto the slender part of the twistandfit curtain rod to ensure it’s about two inches away from the part that is thicker.

Holding the curtain rod with one-hand at every end, twist the rod clockwise to shorten it or counter-clockwise to lengthen it, before the distance between both tabs that protrude from every end of the rod is the same as the window measurement.

So the two tabs are to the rear, turn the curtain rod. Position the rod just just beneath the leading edge of the window opening. Insert the tabs to the window opening, modifying them when they’re slim or too broad.

Remove the twist-and-fit curtain rod in the window and slide the curtains.

Hold the curtain rod straight back in to location in the window opening. Until the tabs fit tightly from the sides of the opening twist the rod counter-clockwise.

Let go to check whether it’ll will remain in position. Include more pressure by twisting it counter-clockwise in case it slips.

The rubber ring to the thicker aspect in the side of the rod. The rubber ring holds the two-pieces together and maintains the stress that is suitable.

See related

How to Deep Clean Your Carpets

While carpets are a really common and comfortable floor surface, maintaining them does take a bit of work. However, regular carpet cleaning Tucson AZ combined with deep cleaning every now and then is a great way to stay on top of things. Carpet cleaning requires the use of very specific but simple tools and products, including some borax, salt, and white vinegar, as well as a steam cleaner and vacuum cleaner.


Here are some great Tucson carpet cleaning tips to help you effectively deep clean your carpet so that it looks and feels like new again:

  1. Start by tidying up first. You want the space to be clear so that it’s easier to remove the bigger items from the room later. Next, vacuum the carpet very thoroughly, while making sure you move the vacuum from one end of the room to the next and back. Repeat until you feel as though you’ve removed all the dirt, dust and debris from the carpet.
  2. Make a cleaning solution of a ¼ cup each of the aforementioned ingredients of salt, white vinegar and borax to form a paste-like consistency. Rub this paste onto the carpet, focusing on all the difficult stains and smears that you’ve been having difficulty cleaning. Leave the paste to soak on the carpet stains for several hours and then use your vacuum to remove it once it’s completely dried up.
  3. Fill the steam cleaner with about 2.5 gallons of super-hot water and a cup of white vinegar to completely remove stubborn grime and stains.
  4. Most steamers switch between two modes that involve releasing and sucking water, and your goal is to use the second mode more than the first one, while soaking the carpet in between to get a really deep clean.
  5. After you’ve gone through your entire carpet with the steam cleaner, repeat the process again to get your money’s worth from the rented steamer. You probably won’t do this type of deep carpet cleaning Tucson again for another year so you should do it right while you’re on the job.
  6. Allow the carpet to completely dry out before putting your furniture back into the room. To be on the safe side, place a few pieces of aluminum foil under the sofa and table legs to avoid any fresh stains getting from on the carpet. Also refrain from walking on the carpet at all until you’re absolutely sure that it’s dry. Preferably wait for a day or two in the winter time, or just overnight if it’s summer, as you’re most likely able to open the doors and windows to let the air in and dry it faster.
  7. End your carpet deep cleaning fun on an eco-friendly note by disposing of the water cleaning solution inside the steam cleaner in a responsible way. If you’re not sure how to do this, consult with your local water treatment plant authorities for help and clarity.

The best way to Imitate Tile

Few components can best tile in regards to providing your ground, wall or backsplash a striking seem. When it is stylish marble or shiny ceramic, austere stone, tile instantly transforms an area right into the focal point of a room. Installing tile, nevertheless, could be a costly, time consuming task which will not suit your remodeling ideas. Fortunately, tile can be imitated by you with methods and components to ensure you get the look and feel at a small percent of the price and work of it.

Use Laminate

When you want to imitate tile for the floor, laminate flooring is a choice that is ideal as it’s often designed to resemble stone or ceramic tile. But tile is generally less costly than other and ceramic tile choices as it’s made from high-density fiber board that’s covered with resin-impregnated paper as well as a wear layer that is clear. Tile is a flooring materials that is highly-durable, therefore it works particularly well in rooms that see high-traffic, such as living room, the kitchen or hall way. Because it’s simpler to clean and preserve than actual tile, laminate tile also is useful in mudrooms and entryways. Generally, it is possible to install tile over existing flooring, creating the installation a project that is easy and quick. While it’s used mainly for flooring tile can mimic the appearance of tile to get back splash or a wall.

Paint It

It is possible to imitate the appearance of tile in the event you appreciate c-Reative jobs. Much like laminate flooring, painting fake tiles could be a quick -pleasant method. Painting, nevertheless, permits one to customize the appearance of your tile depending on your own decor. Painting fake tile is an especially excellent alternative for vertical surfaces just like an accent and back-splash wall. Start by utilizing painter’s tape to produce a grid on your faux tile – you are able to create the tiles in just about any size which you like and even use a couple of sizes to a-DD dimension to the seem. Squares perform nicely in the event that you if you wish to to paint with diverse colours, while squares that are bigger are your most readily useful wager in case your want a stylish, mono-chromatic seem. To get a more genuine texture, include sand to your own paint or rub a few of the paint from the middle of each “tile” using a rag to give them the look of handmade tiles. In the event that you prefer the appearance of shiny ceramic tiles, select a large-gloss paint to fill-in your “tiles.”

Apply Plaster

If imitating tile with paint doesn’t offer enough texture to offer you as practical an appear as you’d like, consider utilizing Venetian plaster to generate fake tiles that have a threedimensional quality for the backsplash or wall. For the genuine look, blend plaster in a number of different shades to generate custom shade variants on the list of tiles that are faux. Start by within the the wall using a basecoat of paint which is similar to the plaster shade that is lightest which you plan to use. When the paint h-AS dried, use painter’s tape to produce a grid in your wall – the tape will also assist generate the appearance of grout lines subsequent to the plaster was applied. Start using the shade of plaster and use it to the wall using a plaster blade, operating all the way through. After the darkish shade is dry follow together with the medium plaster shade, and permit it to dry entirely. Gently eliminate the painter’s tape and protect the location using a a skinny coat of the lightest plaster shade, filling out the “grout” lines too. Following the plaster is dry, use an electrical sander to wear locations of the wall to produce sustained colour variation. Finish up by buffing the fake tile with wax to get a really genuine seem.

Hang Wall Paper

If you’re searching for the fastest, simplest way to imitate tile on a-wall or backsplash, fake tile wall-paper is your greatest wager. Made from a vinyl materials, the wall paper comes in an assortment of styles that mimic Spanish, marble, ceramic and other type s of tile. To save lots of time, fake tile wall paper which is pasted to make the program easier can be found by you. If you’re using the wall-paper to get a back-splash location, make sure it may be scrubbed having a moist sponge or fabric s O which you can easily clear grease, oil, water marks and other grime and particles which will accumulate.

See related

Tips on Relocating a Hot-Water Heater In To Another Room

Moving a hot water heater to your new place in a house is a process that is challenging and requires considerable planning and preparing. You’ll need to become familiar with local building codes associated with water heater installation. You’ll need to know transfer supply lines to the new place, and the best way to reroute water lines. Then the legislation demands which you hire a contractor to transfer the fuel service lines in case your hot water heater is gas-operated. That is not a task for an in-experienced do-it-yourself-er; it’s possibly hazardous and complicated. You need to consult using a contractor though you if you choose to to transfer yourself to the hot water heater.

Prepare the New Place

Relocating plumbing to to allow for the new area for the hot water heater will will need so that you can install the pipes, fittings, and electrical lines in the wall one to open walls. Water heaters need venting, and that means you’ll need to install a fresh pipe, which should exit the framework through the roof. You’ll need to become familiar with flashing and roofing methods, as well. Many local codes could also need earthquake strapping, and require the installation of hot-water heaters on elevated platforms. These extra needs will improve labor expenses and your materials.

Tips on Disconnecting Hotwater Heaters

To disconnect the water heater from your water lines you will need to shut the water off to the complete home first. Next, switch on two taps, one established on chilly, and one established on warm; this drains the water lines as well as the warm water heater’s tank. It’s safe to disconnect the water lines in the water heater after the water entirely drains. When disconnecting the heated water line, use caution. When disconnecting a warm water heater from electric power, flip off the breaker for the hotwater heater in fuse-box and the panel first. Near the valve on the fuel line before disconnecting the heated water heater in the gas line. Don’t do your self to the fuel line-work.

Tips on Relocating a Warm Water Heater

When relocating a hot water heater it’s essential which you move it in a horizontal placement, and that you’re gentle with it. Location some thing between the dolly and also the water-heater to cushion it, although you can use an equipment dolly using a strap. Use caution when shifting the waterheater. The the inner of the waterheater is very fragile and susceptible to injury from vibration during movement.

Hot Waterheater reconnecting Ideas

Before shifting the waterheater in to placement always verify and pressurize the new water-pipes for leaks. Turn on a coldwater faucet before you change the water straight back to the house, and once you link the hotwater heater to the water lines. After the air is bled-from the water line that is cold, change off the coldwater, as a way to bleed the air out of the lines and turnon the hotwater. Don’t change off the gasoline to the whole residence when re-connecting the waterheater to the gasoline line that is new. When you flip the gasoline again on, in the event you do every one of the pilot lights in the home is going to be off. Always use the valve to the water-heater to to manage fuel movement to the hot water heater next on the gas line.

See related